2" Diameter Stainless Steel Mandrel Bent 90 degree elbow with 6" legs. Centerline Radius 3" (medium radius). 304 Grade / T304 SS, 16 Gauge (.065") corrosion resistent tubing. Easy to cut and use to fab downpipes, exhaust systems, intake systems, and intercooler pipes. Made
Nominal Wall 90° 3R Elbows 45° 3R Elbows Nominal Thickness Approx. Weight, lbs. Approx. Weight, lbs. Pipe Size Standard Wall Extra Strong Wall Center to End (A) Standard Wall Extra Strong Center to End (A) Standard Wall Extra Strong 2 .154 .218 6 3.0 4.0 2.5 1.5 2.0 3 .216 .300 9 9.2 12.4 3.75 4.6 6.1 90 Degrees Elbow Sanitary Tube Fittings - Tube Fittings 90 Degree Long Tangent Elbows Purchased products For permanent installations where process lines and equipment can be cleaned in-place without disassembly, these versatile fittings are suitable for use in the food, dairy, beverage, pharmaceutical, and biotech industries.
90° and 45° Long Radius Elbows - ANSI B16.9 Dimensions (based on ASME/ANSI B16.9) and example weights for long radius elbows Common 90° Elbow 45° Elbow Nominal Pipe Size OD at Bevel Dimension 40S/STD1 Dimension 40S/STD1 in mm in mm kg/piece in mm kg/piece 1/2 0.84 21 1.50 38 0.08 0.62 16 0.04 Butt Weld 90 Degree Elbow Tangent FittingButt weld 90 degree elbow fittings with tangents are offered in 0.75 to 6 inch diameter stainless steel vacuum tubing. These elbows have radius equal to 1.5x the tubing diameter and straight tangent section on each end. Elbows are used to make a right angle change of direction in vacuum tubing. 90° butt weld elbows with tangents.
Typical tangent lengths are 2+ but longer (and custom upon request) tangents are available. What is the same about tangent pipe fittings? When manufactured, IAW ANSI B16.9, pipe fitting elbows can be LR (Long Radius) 1.5xDIA or SR (Short Radius) 1.0xDIA in both 90 degree form and 45 degree form. Tangent pipe fitting elbows can also be Mild Steel Elbows:90 Degree Mandrel Bend 1010 Mild 90 Degree Mandrel Bent Mild Steel Tubing Elbows bent from 1010 Mild Steel with 16 Gauge walls. Smooth and true, wrinkle free 90 Degree Elbows for custom fabrication of
90° Elbow with Two 4" Tangents These Elbows have no visible seam unless noted. Pipe Miscellaneous Radius Pipe and OD Tube Elbows. 38 ISO 9001:2008 F 414 214 0450 90° and 180° Elbows with tangents are mandrel bent and have no seam. The 1" inside radius on these Tube Fitting / Elbow / Square / Steel / 90°part number:square tube clr:tangent:lbs ea:zh120-6200:1" x 1" x .120" 3" 4" 0.57# zh120-6220:1-1/4" x 1-1/4" x .120" 3" 4" 0.71# zh120-6240:1-1/2" x 1-1/2" x .120"
Oct 14, 2009 · Previousley I was using single wall pipe with a 45 elbow to an 18 inch run and 90 elbow out to the thimble. I have an exterior chimney with a 9x13 clay liner. I was told with the double wall pipe I will need an adapter off the stove. The thing is with an adapter and then the 45 elbow I will be too high and pass above the thimble. Weld Fittings:90 Degree Weld Elbows w/ Tangents, 3A B2S Stainless Steel 90 Degree Weld Fittings with tangent Extensions are available with either a mill ID/OD or a 32Ra ID/OD polished finish in your choice or 304 or 316L stainless steel. These Buttweld 90 Degree Weld Elbows with Tangents are manufactured to very high tolerances via hydroforming.
Bent 90° Pipe & Tube Elbows with Two Tangents. These mandrel bent elbows have no visible seam. Stainless 1-1/4" pipe, 1-1/2" pipe, and 1-1/2" O.D. tubing elbows are bent with pre-polished material and may require some touch-up. Most sizes available in multiple radii.